Phone · Motorola · Moto Edge 30 Fusion
Motorola Moto Edge 30 Fusion Screen Replacement
Screen Replacement guide for the Motorola Moto Edge 30 Fusion
Before you begin
Tools
- Heat gun or hairdryer
- Suction cup
- Plastic opening picks
- Spudger
- Precision Phillips screwdriver
- Tweezers
Parts / materials
- Replacement screen assembly
- Pre-cut screen adhesive strips
- Pre-cut back panel adhesive strips
- Isopropyl alcohol (90%+)
- Microfiber cleaning cloth
Safety
- Wear safety glasses to protect your eyes from flying glass fragments.
- Discharge the battery below 25% before starting the repair to prevent thermal hazards.
- Work in a well-ventilated area when using isopropyl alcohol.
Overview
Step-by-step
- 1
Power off the phone
1 minPress and hold the power button, then tap Power Off on the screen to completely shut down the device.
- 2
Heat the rear glass panel
2 minApply a heat gun set to low heat along the edges of the rear panel for two minutes to soften the underlying adhesive.
- 3
Attach a suction cup
1 minPlace a suction cup on the lower third of the rear glass and pull upward firmly to create a slight separation gap.
- 4
Slice the rear adhesive
3 minInsert a plastic opening pick into the gap and slide it along all four edges to cut through the back panel adhesive.
- 5
Remove the rear panel
1 minGently lift the rear glass panel away from the chassis and place it on a clean surface.
- 6
Unscrew the motherboard cover
2 minRemove the Phillips screws securing the plastic upper cover and wireless charging coil frame.
- 7
Detach the motherboard cover
1 minInsert a spudger under the motherboard cover to lift and release it from the retainers.
- 8
Disconnect the battery cable
1 minUse the flat edge of a plastic spudger to pry the battery flex cable directly up from its socket on the motherboard.
- 9
Unscrew the lower speaker housing
2 minRemove the Phillips screws holding the loudspeaker enclosure at the bottom of the phone.
- 10
Remove the speaker housing
1 minPry up the lower speaker module with a spudger and set it aside.
- 11
Disconnect the display flex cable
1 minPry up the press-fit display connector from the daughterboard at the bottom of the device.
- 12
Heat the front display
2 minWarm the front perimeter of the screen with a heat gun for two minutes to soften the display adhesive.
- 13
Slice the screen adhesive
4 minAttach a suction cup to the glass screen, insert an opening pick along the edge, and slide around the frame perimeter.
- 14
Lift off the display assembly
2 minCarefully tilt the screen up and guide its flex cable out through the slot in the midframe.
- 15
Clean the display frame
3 minRemove old adhesive and glass fragments from the inner frame using isopropyl alcohol and a plastic spudger.
- 16
Apply display adhesive
3 minAlign and press pre-cut double-sided adhesive strips along the inner rim of the phone frame.
- 17
Feed flex cables through frame
2 minThread the flex cable of the new display assembly through the frame opening and align the panel with the edges.
- 18
Press display onto frame
2 minGently apply firm, even pressure around the perimeter of the screen to seal it against the frame adhesive.
- 19
Reconnect display and battery cables
2 minSnap the display connector onto the sub-board and reconnect the main battery flex cable to the motherboard.
- 20
Reinstall internal brackets
3 minPosition the speaker module and top motherboard cover back onto the frame, then reinsert and tighten all Phillips screws.
- 21
Reattach the rear panel
2 minApply new adhesive tape to the back frame perimeter and press the rear glass firmly back into place.
After your Motorola Moto Edge 30 Fusion screen replacement
Power the Moto Edge 30 Fusion back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 30 Fusion job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto Edge 30 Fusion repair context in the encyclopedia, or open related DIY guides.
