Phone · Motorola · Moto Edge 30 Fusion
Motorola Moto Edge 30 Fusion Battery Replacement
Battery Replacement guide for the Motorola Moto Edge 30 Fusion
Before you begin
Tools
- Precision Phillips screwdriver set
- Plastic opening picks
- Plastic spudger
- Suction cup
- Plastic opening card
- Heat gun or heated pad
- SIM eject tool
Parts / materials
- Replacement battery for Moto Edge 30 Fusion
- Pre-cut battery adhesive strips
- Rear glass adhesive seal
- Isopropyl alcohol (90%+)
Safety
- Discharge the battery below 25% before starting to prevent thermal runaway risks.
- Wear safety eye protection when handling heat and prying glass.
- Never use sharp metal tools directly against the lithium-ion battery pouch.
Overview
Step-by-step
- 1
Power Off Phone
1 minPress and hold the Power button, then select Power Off to completely turn off the device.
- 2
Eject SIM Card Tray
1 minInsert a SIM eject tool into the hole at the bottom edge to pop out and remove the SIM tray.
- 3
Heat Rear Glass
2 minApply a heat gun or heated pad to the edges of the back cover for two minutes to soften the adhesive.
- 4
Attach Suction Cup
1 minPlace a suction cup on the lower third of the rear glass and pull upward firmly to create a gap.
- 5
Insert Opening Pick
2 minInsert a thin plastic opening pick into the gap created between the rear glass and the frame.
- 6
Slice Edge Adhesive
3 minSlide the pick carefully along all four edges of the phone to cut through the back cover adhesive.
- 7
Lift Off Back Cover
1 minGently lift the rear glass off the chassis and set it aside on a clean surface.
- 8
Unscrew Motherboard Bracket
3 minUse a precision Phillips screwdriver to remove the screws securing the upper protective bracket.
- 9
Remove NFC Antenna Assembly
2 minPry up and remove the plastic motherboard cover along with the attached wireless charging/NFC coil.
- 10
Disconnect Battery Cable
1 minUse a plastic spudger to detach the battery press connector directly from the motherboard.
- 11
Disconnect Display Flex Cable
1 minUnplug the main display interconnect cable running over the battery using the spudger.
- 12
Apply Isopropyl Alcohol
2 minDrip a few drops of high-concentration isopropyl alcohol along the battery edges to dissolve glue.
- 13
Pry Up Battery
4 minInsert a flexible plastic opening card underneath the battery and gently lift it up from the frame.
- 14
Remove Damaged Battery
1 minLift the old battery completely out of the frame and set it aside for proper recycling.
- 15
Clean Battery Recess
2 minWipe away residual glue from the frame recess using isopropyl alcohol and a lint-free cloth.
- 16
Install New Battery Adhesive
2 minApply fresh double-sided battery adhesive tape strips directly into the phone frame recess.
- 17
Set New Battery
1 minPlace the replacement battery into the frame and press down firmly to secure it.
- 18
Reconnect Flex Cables
2 minReattach the display interconnect cable and press the battery connector back into place on the motherboard.
- 19
Reinstall Motherboard Bracket
3 minPosition the top cover and NFC assembly over the motherboard and tighten all securing screws.
- 20
Apply Back Cover Adhesive
2 minPlace custom replacement adhesive tape along the perimeter edges of the phone frame.
- 21
Seal Rear Glass
2 minAlign the back cover with the frame and press firmly along the edges to seal the phone.
After your Motorola Moto Edge 30 Fusion battery replacement
Power the Moto Edge 30 Fusion back on and test the battery replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 30 Fusion job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto Edge 30 Fusion repair context in the encyclopedia, or open related DIY guides.
