Phone · Motorola · Moto Edge 20 Pro
Motorola Moto Edge 20 Pro Screen Replacement
Screen Replacement guide for the Motorola Moto Edge 20 Pro
Before you begin
Tools
- Heat gun or hair dryer
- Phillips #00 screwdriver
- Suction cup tool
- Plastic prying tools
- Spudger tool
- Tweezers
- SIM eject tool
Parts / materials
- Replacement OLED Screen
- Double-sided adhesive strips
- Rear cover replacement adhesive tape
- Isopropyl alcohol (90%+ concentration)
Safety
- Wear safety glasses to protect eyes from fragmented glass during screen removal.
- Discharge battery below 25% to minimize thermal runway risk during disassembly.
- Do not puncture or bend the lithium-ion battery with sharp metal tools.
Overview
Step-by-step
- 1
Remove SIM Card Tray
1 minInsert a SIM eject tool into the hole at the bottom of the phone frame and push firmly to eject the tray.
- 2
Heat Back Panel
2 minApply a heat gun evenly across the perimeter of the back glass for 2 minutes to soften the adhesive.
- 3
Attach Suction Cup
1 minPlace a suction cup on the lower portion of the back panel and pull up firmly to create a small seam.
- 4
Insert Opening Pick
1 minInsert a thin plastic pick into the gap between the rear glass and the aluminum frame.
- 5
Slice Rear Adhesive
3 minSlide the plastic pick along all four edges of the back cover to cut through the perimeter tape.
- 6
Remove Back Panel
1 minLift the rear glass cover completely off the phone body and set it aside.
- 7
Unscrew Midframe Covers
3 minUse a Phillips #00 driver to remove all screws securing the upper motherboard cover and lower speaker assembly.
- 8
Pry Off Upper Cover
1 minInsert a spudger under the motherboard shield and gently pry it off the chassis.
- 9
Pry Off Lower Speaker
1 minLift and remove the lower loudspeaker module from the bottom of the frame.
- 10
Disconnect Battery Cable
1 minUse the flat edge of a spudger to pry the battery flex connector straight up from the motherboard.
- 11
Disconnect Display Flex
1 minUnplug the main display cable connector located near the bottom of the motherboard assembly.
- 12
Heat Display Glass
3 minApply heat across the front screen for 2 to 3 minutes to soften the display panel adhesive.
- 13
Pry OLED Assembly
4 minAttach a suction cup to the front screen, pull up, and slide a plastic pick around the display perimeter to separate it.
- 14
Remove Screen Assembly
2 minCarefully guide the screen flex cable through the slot in the frame and remove the broken panel.
- 15
Clean Frame Residue
3 minScrape away old adhesive residue from the frame ledge using isopropyl alcohol and a spudger.
- 16
Apply Display Adhesive
3 minLay fresh double-sided adhesive tape along the internal perimeter ledge of the front frame.
- 17
Install Replacement Screen
2 minThread the new display flex cable through the frame slot and press the screen firmly into place.
- 18
Reconnect Flex Cables
2 minSnap the display flex connector and battery connector back onto the motherboard until they click.
- 19
Reinstall Midframe Covers
3 minPosition the upper shield and lower speaker box over the components and tighten all Phillips screws.
- 20
Reseal Back Glass
2 minApply fresh rear cover adhesive, align the back panel with the frame, and press firmly along edges to seal.
After your Motorola Moto Edge 20 Pro screen replacement
Power the Moto Edge 20 Pro back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 20 Pro job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto Edge 20 Pro repair context in the encyclopedia, or open related DIY guides.
