Phone · Motorola · Moto E6 Play
Motorola Moto E6 Play Logic Board Repair
Logic Board Repair guide for the Motorola Moto E6 Play
Before you begin
Tools
- Phillips #000 Screwdriver
- Plastic prying tools
- Spudger tool
- Tweezers
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Replacement Moto E6 Play Logic Board
- Isopropyl alcohol 90%+
Safety
- Wear an anti-static wrist strap connected to a grounded surface to avoid ESD damage.
- Always disconnect the battery press connector before removing or installing internal components.
- Do not puncture or bend the internal battery when working inside the chassis.
Overview
Step-by-step
- 1
Power Off the Phone
1 minPress and hold the power button until the options menu appears, then tap Power Off. Ensure the screen turns completely dark before continuing.
- 2
Eject the SIM Tray
1 minInsert a SIM eject tool or straightened paperclip into the hole next to the SIM tray. Push firmly to pop the tray out and remove it.
- 3
Unclip the Back Cover
3 minInsert a plastic prying tool into the seam between the rear cover and the display assembly near the SIM card slot. Pry along the perimeter to release the plastic clips.
- 4
Disconnect the Fingerprint Cable
2 minGently lift the back cover off, taking care not to strain the attached ribbon cable. Use a spudger to detach the fingerprint sensor connector from the logic board.
- 5
Remove Motherboard Bracket Screws
3 minUnscrew the Phillips #000 screws securing the plastic motherboard protective cover. Store the screws in a organized tray.
- 6
Lift Off the Motherboard Shield
2 minInsert the flat end of a spudger under the edge of the motherboard shield. Gently pry up to unclip and remove it from the housing.
- 7
Disconnect the Battery Flex Cable
1 minUse a plastic spudger to pry the battery press connector straight up off the board. Disconnecting power prevents electrical damage during repairs.
- 8
Disconnect Display and Interconnect Cables
2 minPry up the display flex cable and main interconnect cable press connectors from the logic board using the flat end of a spudger.
- 9
Unplug the Antenna Cable
2 minUse precision tweezers to grab the head of the coaxial antenna cable near its socket. Gently pry straight up to disconnect it from the logic board.
- 10
Remove Logic Board Retaining Screws
2 minUnscrew the remaining Phillips #000 screws holding the logic board to the inner chassis.
- 11
Pry Up the Logic Board
3 minInsert a spudger under the bottom edge of the logic board and gently lever it upward out of the phone body.
- 12
Transfer the Camera Modules
4 minDisconnect the front and rear cameras from the old logic board using a spudger. Reattach them immediately to the new replacement logic board.
- 13
Position the Replacement Logic Board
2 minAlign the replacement board over the chassis screw posts. Press down gently until it rests flat inside the frame.
- 14
Reconnect All Antenna and Flex Cables
3 minSnap the coaxial cable back onto its socket using tweezers, then press the display and interconnect flex connectors firmly into place.
- 15
Secure the Board and Reconnect Battery
3 minFasten the board with its retaining screws, then press the battery flex cable firmly into its socket to restore power.
- 16
Reinstall Shield and Reassemble Housing
4 minSnap the fingerprint flex cable into place, reinstall the plastic motherboard shield with screws, and snap the rear cover back onto the frame.
After your Motorola Moto E6 Play logic board repair
Power the Moto E6 Play back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto E6 Play job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto E6 Play repair context in the encyclopedia, or open related DIY guides.
