Skip to main content
logo

Phone · Motorola · Moto E 2nd Gen

Motorola Moto E 2nd Gen Water Damage Repair

Water Damage Repair guide for the Motorola Moto E 2nd Gen

Expert
~54 min
14 steps

Before you begin

Tools

  • T4 Torx screwdriver
  • Plastic prying tools
  • Spudger tool
  • Tweezers
  • Soft brush
  • Compressed air

Parts / materials

  • Isopropyl alcohol (99%)
  • Lint-free microfiber cloth
  • Shallow cleaning tray

Safety

  • Always disconnect the battery immediately to prevent electrical short circuits.
  • Work in a well-ventilated area when using 99% isopropyl alcohol.
  • Wear eye protection when spraying compressed air near liquids.

Overview

# Motorola Moto E 2nd Gen Water Damage Repair Repair Guide Action-specific water damage repair walkthrough for the Motorola Moto E 2nd Gen. About 54 minutes across 14 steps. This DIY guide walks through water damage repair on the Motorola Moto E 2nd Gen (Moto E series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the Moto E 2nd Gen specifically—not a similar Moto E sibling. Most DIY techs finish this Motorola Moto E 2nd Gen water damage repair in about 54 minutes when parts and tools are ready. Difficulty is rated expert for this model. Recommended tools for this Motorola Moto E 2nd Gen job: T4 Torx screwdriver, Plastic prying tools, Spudger tool, Tweezers, Soft brush, Compressed air. Parts and supplies: Isopropyl alcohol (99%), Lint-free microfiber cloth, Shallow cleaning tray. Power the Moto E 2nd Gen off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola Moto E 2nd Gen, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle water damage repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power Off Device

    1 min

    Turn off the Moto E completely to prevent electrical short circuits. Do not attempt to charge or power on a wet phone.

  2. 2

    Remove Grip Band

    2 min

    Insert a fingernail or plastic pick into the bottom notch and peel the outer rubberized grip band away from the body.

  3. 3

    Remove SIM and MicroSD Cards

    1 min

    Pull out any installed SIM card and MicroSD card from their respective side slots.

  4. 4

    Unscrew Rear Frame Screws

    4 min

    Use a T4 Torx screwdriver to remove the 14 screws securing the inner plastic midframe.

  5. 5

    Unclip Rear Frame

    3 min

    Insert a plastic prying tool into the seam along the edge and pry around the perimeter to release the plastic clips.

  6. 6

    Disconnect Battery Connector

    2 min

    Use a spudger to carefully flip up the retaining clip on the battery ZIF connector, then slide the flex cable out.

  7. 7

    Pry Out Battery

    3 min

    Gently insert a plastic opening pick under the battery to break the light adhesive and remove it from the frame.

  8. 8

    Disconnect Display Flex Cable

    2 min

    Flip up the locking tab on the display ZIF socket using a spudger and pull the ribbon cable free.

  9. 9

    Lift Out Motherboard

    3 min

    Pry gently beneath the edges of the main motherboard to unhook it from the plastic chassis.

  10. 10

    Submerge Motherboard in Isopropyl Alcohol

    5 min

    Place the motherboard in a shallow container filled with 99% isopropyl alcohol to displace trapped water.

  11. 11

    Scrub Corrosion with Soft Brush

    5 min

    Use a soft brush soaked in 99% isopropyl alcohol to gently scrub away visible liquid deposits and corrosion.

  12. 12

    Displace Liquid with Compressed Air

    3 min

    Use short bursts of compressed air to clear remaining alcohol and moisture from under micro-components and shields.

  13. 13

    Dry Components Thoroughly

    15 min

    Lay the cleaned components flat on a lint-free cloth and let them air dry completely in a warm area.

  14. 14

    Reassemble and Test Device

    5 min

    Reinstall the motherboard, battery, and rear frame, then power on the device to test full functionality.

After your Motorola Moto E 2nd Gen water damage repair

Power the Moto E 2nd Gen back on and test the water damage repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto E 2nd Gen job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola Moto E 2nd Gen repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll Moto E 2nd Gen guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.