Skip to main content

Phone · LG · G8X ThinQ

LG G8X ThinQ Battery Replacement

Battery Replacement guide for the LG G8X ThinQ

Moderate
~43 min
20 steps

Before you begin

Tools

  • Heat gun or iOpener
  • Suction cup
  • Opening picks
  • Phillips #00 screwdriver
  • Plastic spudger
  • Plastic opening cards
  • Tweezers
  • Anti-static wrist strap

Parts / materials

  • Replacement battery for LG G8X ThinQ
  • Pre-cut battery adhesive strips
  • Pre-cut rear glass adhesive gasket
  • 99% Isopropyl alcohol
  • Lint-free cloth

Safety

  • Wear eye protection to guard against sharp glass fragments if the rear panel is cracked.
  • Do not pry against the lithium-ion battery with sharp metal tools.
  • Avoid bending or puncturing the battery during removal to prevent a thermal event.
  • Work in a well-ventilated area when using isopropyl alcohol or solvent.

Overview

# LG G8X ThinQ Battery Replacement Repair Guide Action-specific battery replacement walkthrough for the LG G8X ThinQ. About 43 minutes across 20 steps. This DIY guide walks through battery replacement on the LG G8X ThinQ (G Series series phone). Before you open the device, confirm the exact model number on the LG settings screen or rear housing so your replacement part matches the G8X ThinQ specifically—not a similar G Series sibling. Most DIY techs finish this LG G8X ThinQ battery replacement in about 43 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this LG G8X ThinQ job: Heat gun or iOpener, Suction cup, Opening picks, Phillips #00 screwdriver, Plastic spudger, Plastic opening cards, Tweezers, Anti-static wrist strap. Parts and supplies: Replacement battery for LG G8X ThinQ, Pre-cut battery adhesive strips, Pre-cut rear glass adhesive gasket, 99% Isopropyl alcohol, Lint-free cloth. Power the G8X ThinQ off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your LG G8X ThinQ, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle battery replacement for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power off the device

    1 min

    Press and hold the power button, then tap Power Off on the screen. Ensure the phone is completely shut down before continuing.

  2. 2

    Heat the rear glass

    3 min

    Apply a heated iOpener or heat gun around the perimeter of the back cover for two minutes to soften the adhesive.

  3. 3

    Attach a suction cup

    1 min

    Place a suction cup near the bottom edge of the rear glass panel and press down firmly to secure a grip.

  4. 4

    Lift the rear glass

    2 min

    Pull up on the suction cup to create a small gap between the glass cover and the phone frame.

  5. 5

    Insert an opening pick

    2 min

    Slide a thin plastic opening pick into the gap created at the bottom edge.

  6. 6

    Slice the perimeter adhesive

    4 min

    Slide the pick around all four edges of the rear glass to cut through the factory adhesive layer.

  7. 7

    Remove the rear cover

    1 min

    Carefully lift the rear glass off the device chassis and set it on a clean surface.

  8. 8

    Unscrew the midframe

    4 min

    Remove the 15 Phillips #00 screws securing the upper wireless charging pad and lower speaker module.

  9. 9

    Remove the wireless charging coil

    2 min

    Gently pry up and remove the upper midframe shield containing the wireless charging and NFC coil.

  10. 10

    Remove the loudspeaker assembly

    2 min

    Use a plastic spudger to lever the lower loudspeaker module up and out of the housing.

  11. 11

    Disconnect the battery cable

    1 min

    Pry the battery connector straight up from its motherboard socket using a plastic spudger.

  12. 12

    Disconnect the main interconnect cable

    1 min

    Pop off the main interboard flex cable connector covering the lower section of the battery.

  13. 13

    Apply adhesive remover

    2 min

    Apply a few drops of high-concentration isopropyl alcohol along the top and bottom edges of the battery well.

  14. 14

    Wait for adhesive to soften

    2 min

    Allow the isopropyl alcohol to soak for two minutes to weaken the strong battery tape underneath.

  15. 15

    Pry up the battery

    3 min

    Insert a flat plastic opening card beneath the side of the battery and slowly lever it upward.

  16. 16

    Remove the old battery

    1 min

    Lift the depleted battery out of the frame, taking care not to bend or puncture the pouch.

  17. 17

    Clean the battery compartment

    2 min

    Wipe away remaining adhesive residue inside the recessed battery frame using isopropyl alcohol and a lint-free cloth.

  18. 18

    Apply new battery adhesive

    2 min

    Lay pre-cut double-sided adhesive strips into the battery well and peel away the protective film.

  19. 19

    Install the new battery

    2 min

    Position the replacement battery into the frame, press down firmly to adhere, and reconnect its flex cable.

  20. 20

    Reinstall internal components

    5 min

    Reconnect the main ribbon cable, reseat the lower speaker and upper wireless charging module, then tighten the 15 Phillips screws.

After your LG G8X ThinQ battery replacement

Power the G8X ThinQ back on and test the battery replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this LG G8X ThinQ job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more LG G8X ThinQ repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.