Skip to main content
logo

Phone · LG · G6

LG G6 Screen Replacement

Screen Replacement guide for the LG G6

Difficult
~43 min
22 steps

Before you begin

Tools

  • Heat gun or hair dryer
  • Suction cup tool
  • Plastic prying tools
  • Phillips #00 screwdriver
  • Spudger tool
  • Tweezers

Parts / materials

  • Replacement display assembly with frame
  • Double-sided adhesive strips

Safety

  • Wear eye protection when applying heat to glass
  • Use an anti-static wrist strap to protect electronic components from ESD
  • Do not bend or puncture the lithium-ion battery

Overview

# LG G6 Screen Replacement Repair Guide Action-specific screen replacement walkthrough for the LG G6. About 43 minutes across 22 steps. This DIY guide walks through screen replacement on the LG G6 (G Series series phone). Before you open the device, confirm the exact model number on the LG settings screen or rear housing so your replacement part matches the G6 specifically—not a similar G Series sibling. Most DIY techs finish this LG G6 screen replacement in about 43 minutes when parts and tools are ready. Difficulty is rated advanced for this model. Recommended tools for this LG G6 job: Heat gun or hair dryer, Suction cup tool, Plastic prying tools, Phillips #00 screwdriver, Spudger tool, Tweezers. Parts and supplies: Replacement display assembly with frame, Double-sided adhesive strips. Power the G6 off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your LG G6, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle screen replacement for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power off the phone

    1 min

    Press and hold the power button on the back of the device, then tap Power Off on the screen.

  2. 2

    Heat the rear glass panel

    2 min

    Apply heat around the perimeter of the back cover for 2 minutes to soften the adhesive.

  3. 3

    Attach suction cup

    1 min

    Place a suction cup on the lower half of the rear glass and pull upward gently to create a gap.

  4. 4

    Slice rear adhesive

    3 min

    Insert a plastic opening pick into the gap and slide it along the edges to separate the adhesive.

  5. 5

    Lift off rear glass panel

    1 min

    Carefully remove the rear glass panel from the frame and set it aside.

  6. 6

    Unscrew midframe screws

    3 min

    Remove the 11 Phillips #00 screws securing the wireless charging coil and lower speaker cover.

  7. 7

    Remove upper wireless charging pad

    2 min

    Pry up the wireless charging coil assembly from the top frame using a spudger and remove it.

  8. 8

    Remove lower speaker module

    2 min

    Use a spudger to pry up and lift out the loudspeaker module from the bottom of the device.

  9. 9

    Disconnect the battery

    1 min

    Pry the battery connector straight up from the motherboard using the flat end of a spudger.

  10. 10

    Disconnect front-facing camera

    1 min

    Unsnap the front camera connector from the main motherboard.

  11. 11

    Disconnect display flex cable

    1 min

    Pop the display press connector off its socket on the lower section of the motherboard.

  12. 12

    Remove motherboard

    2 min

    Gently lift the motherboard from the bottom end and tilt it out of the chassis.

  13. 13

    Remove earpiece speaker

    2 min

    Use fine tweezers to carefully pry the earpiece speaker out of the top slot of the chassis.

  14. 14

    Remove vibration motor

    2 min

    Insert a flat tool under the coin vibration motor to break its adhesive and remove it.

  15. 15

    Heat front screen to loosen battery glue

    2 min

    Warm the front screen using a heat gun for 1 minute to soften the adhesive beneath the battery.

  16. 16

    Pry out battery

    3 min

    Insert a flat plastic card under the battery and lift slowly until it releases from the frame.

  17. 17

    Install earpiece and vibration motor

    2 min

    Seat the original earpiece speaker and vibration motor into their corresponding slots on the new display frame.

  18. 18

    Place battery into new assembly

    2 min

    Apply double-sided adhesive strips in the battery cavity and press the battery firmly into position.

  19. 19

    Reinstall motherboard

    2 min

    Align the motherboard over the new display frame and press it gently down into place.

  20. 20

    Reconnect display and camera

    2 min

    Snap the display flex cable, front camera connector, and battery connector onto the motherboard.

  21. 21

    Reattach midframe and speaker module

    3 min

    Place the wireless charging coil and loudspeaker back onto the frame, then secure them with the 11 Phillips #00 screws.

  22. 22

    Seal rear glass panel

    3 min

    Apply new adhesive strips along the edges of the frame and press the rear glass firmly closed.

After your LG G6 screen replacement

Power the G6 back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this LG G6 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more LG G6 repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll G6 guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.