Phone · Google · Pixel 7 Pro
Google Pixel 7 Pro Logic Board Repair
Logic Board Repair guide for the Google Pixel 7 Pro
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Opening picks
- Torx T3 screwdriver
- Tweezers
- Spudger tool
- SIM eject tool
Parts / materials
- Isopropyl alcohol (99%)
- Pre-cut display adhesive strips
- Thermal pad/paste
Safety
- Discharge battery below 25% to minimize thermal runaway risk if accidentally punctured.
- Wear an anti-static wrist strap to prevent electrostatic damage to sensitive IC components.
- Wear safety glasses while applying heat and prying glass screens.
Overview
Step-by-step
- 1
Power Off Phone
1 minPress and hold the Power and Volume Up buttons, then select Power Off on the screen. Ensure the device is fully shut down before proceeding.
- 2
Eject SIM Tray
1 minInsert a SIM eject tool or thin paperclip into the small hole on the left edge of the phone. Push inward to pop out the SIM tray and remove it.
- 3
Heat Front Display
3 minApply heat to the front perimeter of the screen using a heat gun on low for 2–3 minutes to soften the display adhesive.
- 4
Attach Suction Cup
2 minPlace a suction cup near the bottom edge of the display screen and pull upward firmly to create a tiny gap.
- 5
Insert Opening Pick
2 minInsert a plastic opening pick into the gap created at the bottom edge. Keep the pick insertion depth under 3mm to avoid damaging internal flex cables.
- 6
Slice Perimeter Adhesive
5 minSlide the pick around the bottom, left, top, and right edges to slice through the adhesive holding the display screen.
- 7
Hinge Display Open
2 minCarefully lift the screen up from the left edge like a book cover. Do not pull it away completely yet, as it remains connected by a display cable.
- 8
Unscrew Display Shield
2 minRemove the two Torx T3 screws holding the metal bracket over the display cable connection.
- 9
Disconnect Display Cable
2 minUse a plastic spudger to pry the display flex cable straight up off its motherboard socket and set the screen aside.
- 10
Unscrew Midframe Plate
4 minRemove the 13 Torx T3 screws securing the midframe and graphite heat shield plate.
- 11
Remove Midframe Shield
2 minUse tweezers or a spudger to lift the midframe plate out of the phone body.
- 12
Disconnect Battery Press Connector
1 minPry the battery press connector straight up off the logic board using the flat end of a spudger to isolate power.
- 13
Disconnect Rear Camera Array
3 minDisconnect the three rear camera flex cables from the top section of the logic board.
- 14
Disconnect Interconnect Cables
3 minUnplug the front camera connector, 5G antenna flex, and lower daughterboard interconnect cables from the motherboard.
- 15
Unscrew Motherboard Anchors
2 minRemove the two Torx T3 screws holding the logic board to the aluminum enclosure.
- 16
Lift Out Logic Board
3 minGently pry up the top edge of the logic board with a spudger and remove it from the phone chassis.
After your Google Pixel 7 Pro logic board repair
Power the Pixel 7 Pro back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Google Pixel 7 Pro job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Google Pixel 7 Pro repair context in the encyclopedia, or open related DIY guides.
