Phone · Apple · iPhone 16e
Apple iPhone 16e Wireless Charging Repair
Wireless Charging Repair guide for the Apple iPhone 16e
Before you begin
Tools
- Pentalobe P2 Screwdriver
- Tri-point Y000 Screwdriver
- Heat Gun or iOpener
- Suction Handle
- Plastic Opening Picks
- Spudger
- Tweezers
Parts / materials
- Replacement iPhone 16e Wireless Charging Coil
- Rear Glass Perimeter Adhesive Gasket
- Isopropyl Alcohol (99%)
Safety
- Wear safety glasses to protect your eyes from fine glass shards.
- Disconnect the internal battery connector before touching logic board components to prevent short circuits.
- Do not puncture or bend the lithium-ion battery while working inside the device.
Overview
Step-by-step
- 1
Power Off and Remove SIM Tray
2 minCompletely turn off your iPhone 16e before starting the repair. Insert a SIM eject tool into the tray hole on the side to pop out the SIM card tray.
- 2
Remove Bottom Pentalobe Screws
2 minUnscrew the two P2 Pentalobe screws located on either side of the bottom charging port.
- 3
Heat the Rear Glass Panel
3 minApply a warm iOpener or heat gun across the back glass for 2 minutes to soften the perimeter adhesive.
- 4
Attach Suction Handle to Rear Glass
2 minPlace a suction cup onto the lower center of the rear glass and pull upward gently to create a small gap.
- 5
Insert Opening Pick Under Edge
2 minInsert a thin opening pick into the seam between the rear glass and the aluminum frame at the bottom edge.
- 6
Slice Perimeter Adhesive Seal
4 minSlide the opening pick slowly around the bottom, left, and right edges to cut through the waterproof adhesive tape.
- 7
Pivot Open the Rear Panel
2 minGently swing the back glass open toward the left side like a book cover, taking care not to strain connected cables.
- 8
Unscrew Logic Board Connector Bracket
3 minUse a Tri-point screwdriver to remove the screws securing the lower metal bracket over the motherboard connectors.
- 9
Disconnect Battery Flex Cable
2 minPry the battery connector straight up from its motherboard socket using the flat edge of a plastic spudger.
- 10
Disconnect Wireless Charging Coil Cable
2 minPry up the press connector for the wireless charging coil assembly from the main logic board.
- 11
Pry Off Old Wireless Charging Assembly
5 minWarm the center of the back glass slightly and gently slice under the wireless charging coil using a plastic pick to detach it.
- 12
Position New Wireless Charging Assembly
3 minPeel the adhesive backing off the replacement wireless charging coil and align it precisely on the interior of the glass panel.
- 13
Reconnect Wireless Charging Flex Cable
2 minAlign the press connector over its motherboard socket and snap it down firmly into place.
- 14
Reconnect Battery and Reattach Bracket
3 minReconnect the battery press cable, replace the metal shield bracket, and secure it with the Tri-point screws.
- 15
Apply Perimeter Frame Adhesive
4 minClean off remaining adhesive residue with isopropyl alcohol, then lay down a fresh pre-cut perimeter adhesive seal.
- 16
Press Rear Panel Closed
3 minAlign the rear panel on the frame and press firmly around all edges to bond the new adhesive seal.
After your Apple iPhone 16e wireless charging repair
Power the iPhone 16e back on and test the wireless charging repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPhone 16e job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPhone 16e repair context in the encyclopedia, or open related DIY guides.
