Phone · Apple · iPhone 11
Apple iPhone 11 Speaker Repair
Speaker Repair guide for the Apple iPhone 11
Before you begin
Tools
- P2 Pentalobe screwdriver
- Y000 Tri-point screwdriver
- Phillips #000 screwdriver
- Suction cup tool
- Plastic spudger
- Opening picks
- Heat gun or hair dryer
- Tweezers
Parts / materials
- Replacement iPhone 11 loudspeaker
- Display adhesive frame seal
- Isopropanol cleaning wipes
Safety
- Always disconnect the battery before handling internal components to prevent short circuits.
- Do not puncture or crush the lithium-ion battery while working near the bottom enclosure.
- Wear safety glasses to protect against potential glass splinters if opening a damaged screen.
Overview
Step-by-step
- 1
Remove Pentalobe Screws
2 minPower off the iPhone completely. Remove the two 3.4 mm P2 Pentalobe screws located on either side of the Lightning charging port.
- 2
Warm Display Adhesive
2 minUse a heat gun or hair dryer to apply mild heat around the bottom perimeter of the display for about two minutes. This softens the water-resistant seal.
- 3
Apply Suction Cup
1 minAttach a suction cup to the lower portion of the front glass, just above the home screen area. Pull up gently to create a small gap between the screen and frame.
- 4
Slice Perimeter Adhesive
3 minInsert an opening pick into the gap along the bottom edge. Slide the pick around the left and right edges to cut through the display adhesive.
- 5
Open Display Assembly
2 minGently swing the display open from the left side to the right, like the cover of a book. Rest the display against a stable object to avoid straining the flex cables.
- 6
Remove Battery Bracket Screws
2 minUse a Y000 tri-point screwdriver to remove the three screws securing the battery connector bracket to the logic board.
- 7
Disconnect Battery Cable
2 minUse tweezers to remove the metal bracket. Pry the battery press connector straight up from its socket on the logic board using a plastic spudger.
- 8
Unscrew Logic Board Cover
2 minRemove the five Y000 screws holding the metal cover plate over the lower display flex cables.
- 9
Detach Display Connectors
3 minRemove the cover plate, then use the flat end of a spudger to disconnect the display and digitizer cables. Set the display assembly aside.
- 10
Remove Loudspeaker Fasteners
2 minUse a Phillips #000 screwdriver to remove the three screws securing the bottom loudspeaker assembly to the rear case.
- 11
Pry Out Loudspeaker
2 minInsert a plastic spudger under the top edge of the speaker module near the Taptic Engine. Gently lever the loudspeaker up and lift it out of the enclosure.
- 12
Install New Loudspeaker
2 minPosition the replacement speaker into the lower chassis, ensuring the contact pads align properly with the logic board grounding points.
- 13
Secure Speaker Screws
2 minReinstall the three Phillips #000 screws to lock the replacement loudspeaker module firmly in place.
- 14
Reconnect Display and Battery
4 minAttach the display flex cables, reinstall their protective shield, then reconnect the battery cable and secure its bracket with the Y000 screws.
- 15
Close Display and Fasten Screws
3 minAlign the top edge of the screen, press the display down into the frame until it snaps flush, and reinstall the two bottom P2 Pentalobe screws.
After your Apple iPhone 11 speaker repair
Power the iPhone 11 back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPhone 11 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPhone 11 repair context in the encyclopedia, or open related DIY guides.
