Console · Sony · PlayStation 5 Slim
Sony PlayStation 5 Slim Fan Replacement
Fan Replacement guide for the Sony PlayStation 5 Slim
Before you begin
Tools
- T8 Torx Security screwdriver
- Plastic opening tools
- Tweezers
- Anti-static wrist strap
- Precision screwdriver set
- Soft microfiber cloth
Parts / materials
- Replacement PS5 Slim fan
- Compressed air duster
- Isopropyl alcohol (91% or higher)
Safety
- Unplug the PS5 Slim from the power outlet and allow 10 minutes for internal capacitors to discharge.
- Wear an anti-static wrist strap to protect internal circuitry from electrostatic discharge.
- Pull directly on the plastic plug when disconnecting the fan to avoid damaging motherboard connectors or tearing wires.
Overview
Step-by-step
- 1
Disconnect external cables
2 minUnplug the AC power cord, HDMI cable, and any USB accessories from the console. Wait 10 minutes for electrical components to fully discharge.
- 2
Remove the base stand
2 minLay the PS5 Slim flat on a soft surface. Remove the stand screw or unclip the mounting feet to detach the stand.
- 3
Pry up the upper left cover panel
2 minLift the rear corner of the top-left outer panel slightly to release the clips. Slide the panel down toward the base to remove it.
- 4
Pry up the upper right cover panel
2 minGently lift the top-right outer cover panel until the internal locking tabs snap free. Slide the panel off the main housing.
- 5
Unclip the intake fan grille
2 minInsert a plastic opening tool under the edge of the plastic fan grille. Pry upward along the border to release the clips and remove the grille.
- 6
Remove the fan bracket screws
3 minUse a T8 Torx Security screwdriver to remove the four screws holding the metal fan cover plate. Note screw locations for reassembly.
- 7
Lift off the metal fan bracket
1 minGasp the edges of the metal fan bracket and lift it straight up off the console housing. Set the bracket aside.
- 8
Disconnect the fan power plug
3 minGrip the fan connector plug with tweezers near the motherboard socket. Gently pull the plug straight out without pulling on the wires.
- 9
Lift the fan from the housing
2 minGasp the fan body and lift it out of the recessed cooling bay. Guide the fan wire carefully through the slot in the plastic frame.
- 10
Clean dust from the fan recess
3 minBlow out remaining dust inside the fan cavity using canned compressed air. Wipe down the plastic mounting edges with a soft microfiber cloth.
- 11
Insert the replacement fan
2 minLower the new cooling fan into the recess, aligning the mounting holes with the chassis posts. Route the cable through the plastic notch.
- 12
Connect the fan power cable
2 minAlign the plug with the motherboard socket. Press the connector firmly into place using tweezers until it fully seats.
- 13
Position the metal fan bracket
2 minPlace the metal fan cover plate back over the fan assembly. Ensure all screw holes line up with the threaded posts.
- 14
Secure the fan bracket screws
3 minDrive the four T8 Torx Security screws clockwise into the bracket until snug. Avoid overtightening to prevent stripping the plastic threads.
- 15
Snap the intake fan grille into place
2 minAlign the plastic fan grille over the intake cutout. Press down firmly along the border until all retaining clips snap into place.
- 16
Reattach the outer cover panels
3 minSlide the upper outer panels back onto the console frame until they firmly click into place.
After your Sony PlayStation 5 Slim fan replacement
Power the PlayStation 5 Slim back on and test the fan replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Sony PlayStation 5 Slim job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Sony PlayStation 5 Slim repair context in the encyclopedia, or open related DIY guides.
