Console · Sony · PlayStation 4
Sony PlayStation 4 Power Supply Repair
Power Supply Repair guide for the Sony PlayStation 4
Before you begin
Tools
- TR9 Security Torx screwdriver
- Phillips #1 screwdriver
- Precision tweezers
- Plastic spudger
- Anti-static wrist strap
- Clean workspace mat
- Good lighting or desk lamp
Parts / materials
- Replacement PS4 Power Supply Unit (ADP-240AR or N14-240P1A depending on revision)
- Isopropyl alcohol (99%)
- Microfiber cloth
Safety
- Unplug the console from all power sources and HDMI cables before starting disassembly.
- Press the power button once while unplugged to discharge any remaining energy in internal capacitors.
- Handle the power supply by its plastic shell to prevent accidental contact with charged high-voltage components.
Overview
Step-by-step
- 1
Peel off rear warranty stickers
2 minUse precision tweezers to pry up and remove the four sticker labels covering the rear screws. This will expose the hidden TR9 security screws.
- 2
Remove rear housing screws
3 minUnscrew the four TR9 Security Torx screws located on the rear panel of the console. Store the screws in a organizer tray to avoid losing them.
- 3
Slide off glossy hard drive cover
2 minPress down gently on the glossy left top panel and slide it outward toward the side of the console. Lift the cover away once it disengages from the clips.
- 4
Unsnap bottom plastic cover
4 minPry up on the rear edges of the bottom housing panel using a plastic spudger. Work around the perimeter until the entire bottom panel releases from the frame.
- 5
Remove power supply bracket screws
3 minUse a Phillips #1 screwdriver to remove the two long screws securing the metal power supply bracket. Lift the metal bracket off the power supply.
- 6
Remove power supply body screws
3 minUnscrew the three TR9 Security Torx screws holding the power supply chassis directly to the inner assembly.
- 7
Disconnect power supply data cable
2 minGrasp the small 5-pin connector attached to the side of the power supply using tweezers or fingers. Pull the connector straight out from its socket, taking care not to yank the wires.
- 8
Lift power supply unit
3 minGrasp the power supply firmly on both sides and lift it straight up from the chassis. The unit disconnects from two prongs underneath, so moderate force may be required.
- 9
Disconnect AC connector cable
2 minUnplug the 2-pin AC power harness from the socket on the underside of the original power supply unit.
- 10
Connect AC cable to new power supply
2 minPlug the 2-pin AC power harness firmly into the underside socket of the replacement power supply.
- 11
Lower new power supply into chassis
3 minAlign the replacement power supply with the internal metal prongs and push down evenly until it sits completely flush.
- 12
Reconnect power supply data cable
2 minPlug the small 5-pin data cable connector back into the matching socket on the side of the new power supply unit.
- 13
Secure power supply body screws
3 minReinstall the three TR9 Security Torx screws to lock the power supply chassis back into the console frame.
- 14
Reinstall power supply bracket screws
3 minPosition the metal power supply bracket over the unit and drive in the two Phillips #1 screws until hand-tight.
- 15
Snap bottom cover onto console
3 minAlign the bottom plastic cover over the chassis and press firmly along the edges until all retaining tabs snap shut.
- 16
Reinstall rear housing screws
3 minThread and tighten the four TR9 Security Torx screws into the rear panel using your driver.
- 17
Slide glossy cover into place
1 minAlign the glossy hard drive cover with the top left side of the console and slide it inward until it locks into place.
After your Sony PlayStation 4 power supply repair
Power the PlayStation 4 back on and test the power supply repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Sony PlayStation 4 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Sony PlayStation 4 repair context in the encyclopedia, or open related DIY guides.
