Console · Microsoft · Xbox Series S
Microsoft Xbox Series S Controller Repair
Controller Repair guide for the Microsoft Xbox Series S
Before you begin
Tools
- TR9 Torx Security Screwdriver
- T6 Torx Screwdriver
- Plastic Opening Picks / Spudger
- Precision Tweezers
- Anti-Static Wrist Strap
Parts / materials
- Isopropyl Alcohol (90%+)
- Cotton Swabs
- Replacement Bumper Assembly
Safety
- Remove all batteries and unplug cables before disassembling the device.
- Wear safety glasses to protect against flying plastic clips or springs.
- Ground yourself with an anti-static wrist strap to avoid damaging delicate integrated circuits.
Overview
Step-by-step
- 1
Remove Battery Cover
1 minSlide the battery door off the back of the controller and remove both AA batteries.
- 2
Pry Left Grip Cover
2 minInsert a plastic pry tool into the seam of the left grip handle and pop the panel free.
- 3
Pry Right Grip Cover
2 minInsert the plastic pry tool into the seam of the right grip handle and release the retaining clips.
- 4
Puncture Security Sticker
1 minPuncture the label inside the center of the battery compartment to expose the hidden screw.
- 5
Remove Handle Screws
3 minUnscrew the four TR9 Torx security screws located on the outer edges of the grips.
- 6
Remove Center Screw
1 minUnscrew the single TR9 Torx security screw from the center of the battery compartment.
- 7
Remove Front Faceplate
1 minLift the front faceplate straight off the body of the controller.
- 8
Remove Rear Shell
1 minPull the rear housing off the back of the inner mid-frame assembly.
- 9
Pull Thumbstick Caps
1 minPull both plastic thumbstick caps straight up and off the joystick shafts.
- 10
Unscrew Top Board
2 minRemove the two T6 Torx screws securing the upper circuit board to the internal plastic frame.
- 11
Unclip Bumper Assembly
2 minGently unhook the plastic tabs securing the top bumper bracket to detach the shoulder buttons.
- 12
Lift Circuit Board Assembly
2 minCarefully tilt and lift the board assembly out of the chassis without straining the haptic motor wires.
- 13
Clean Potentiometer Contacts
3 minDip a cotton swab in isopropyl alcohol and wipe down the analog stick sensors and button pads.
- 14
Realign Board in Chassis
2 minLower the circuit board assembly back into the frame, verifying the rumble motors are correctly seated.
- 15
Reattach Bumper Assembly
2 minAlign the bumper assembly with the top of the frame and press firmly until the clips snap in.
- 16
Press On Thumbstick Caps
1 minAlign the plastic thumbstick caps with the D-shaped metal posts and push them fully down.
- 17
Secure Board Screws
2 minDrive the two T6 Torx screws back into the upper circuit board.
- 18
Reassemble Outer Enclosure
2 minFit the front faceplate and rear shell back together around the internal frame.
- 19
Fasten Housing Screws
3 minInstall the five TR9 Torx security screws into the handle grips and battery compartment.
- 20
Snap On Grip Panels
2 minPress the left and right grip panels back onto the handles until all clips lock flush.
After your Microsoft Xbox Series S controller repair
Power the Xbox Series S back on and test the controller repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Xbox Series S job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Xbox Series S repair context in the encyclopedia, or open related DIY guides.
