Console · Microsoft · Xbox One S
Microsoft Xbox One S Water Damage Repair
Water Damage Repair guide for the Microsoft Xbox One S
Before you begin
Tools
- TR10 Security Torx Screwdriver
- TR8 Security Torx Screwdriver
- Plastic Spudger
- Soft Brush
- Anti-static wrist strap
- Tweezers
Parts / materials
- 99% Isopropyl alcohol
- Compressed air
- Lint-free wipes
- Microfiber cloth
Safety
- Ensure the console is completely disconnected from power source before starting work.
- Wear an anti-static wrist strap to prevent electrostatic damage to logic board components.
- Perform cleaning in a well-ventilated area to avoid inhaling isopropyl alcohol fumes.
- Verify all liquid and cleaning alcohol have fully dried before reassembling and powering on.
Overview
Step-by-step
- 1
Disconnect Power and External Cables
1 minUnplug the AC power cord, HDMI cable, and any USB peripherals from the console. Never attempt liquid damage repair on a powered device.
- 2
Pry Off the Bottom Plastic Cover
3 minUse a plastic spudger to pop the clips securing the lower rear plastic panel. Work your way around the edges until the cover releases.
- 3
Remove Upper Case Screws
4 minUse a TR10 Security Torx screwdriver to remove the long green screws securing the upper metal chassis to the bottom shell.
- 4
Lift Off the Outer Shell
2 minSeparate the top white outer plastic shell from the internal metal body and lift it clear.
- 5
Unscrew Upper Metal Shield
5 minRemove the remaining TR10 and TR8 Torx screws fastening the top metal internal shield plate.
- 6
Remove the Top Metal Shield
2 minLift the top metal cover straight up to expose the internal components.
- 7
Disconnect the Optical Drive
3 minUnplug the SATA cable and power connector from the rear of the optical drive. Lift the drive out of the chassis.
- 8
Remove the Hard Drive Assembly
3 minLift the hard drive bracket slightly, unplug its SATA and power connectors, and remove the drive completely.
- 9
Disconnect the Wi-Fi and Bluetooth Boards
4 minRemove the TR8 screws securing the wireless board and front RF power module, then unplug them from the motherboard.
- 10
Remove the Internal Power Supply
3 minDisconnect the main power connector from the motherboard and lift the internal PSU block out of the metal frame.
- 11
Unfasten the Motherboard
5 minRemove all remaining TR8 screws holding the main logic board to the lower metal housing.
- 12
Lift the Motherboard from the Frame
2 minGently lift the motherboard by its edges out of the bottom chassis. Avoid touching exposed thermal paste on the underside heatsink.
- 13
Inspect Board for Liquid Residue
5 minExamine both sides of the motherboard, ports, and trace pathways using a magnifying glass to locate corrosion or mineral deposits.
- 14
Clean Corroded Areas with Isopropyl Alcohol
10 minDip a soft brush in 99% isopropyl alcohol and gently scrub away corrosion, dried liquid, and oxidation from affected components.
- 15
Clean Ribbon Connectors and Expansion Ports
5 minUse lint-free wipes soaked in isopropyl alcohol to thoroughly clean all cable connections and interface ports.
- 16
Blow Dry Components with Compressed Air
3 minUse compressed air to blast away remaining liquid residue and speed up alcohol evaporation from under IC chips.
- 17
Allow Air Drying
15 minLeave the board in a well-ventilated area for at least 30 minutes to ensure every trace of moisture has evaporated.
After your Microsoft Xbox One S water damage repair
Power the Xbox One S back on and test the water damage repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Xbox One S job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Xbox One S repair context in the encyclopedia, or open related DIY guides.
